Home »
Academic Articles »
C »
Effect of heat treatment on the microstructure and corrosion resistance of laser powder bed fusion ODS-316L
Effect of heat treatment on the microstructure and corrosion resistance of laser powder bed fusion ODS-316L
Qian Zheng
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China; School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou, 730050, Gansu, PR China)
Chao Lu
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China; Corresponding author.)
Yan Yin
(School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou, 730050, Gansu, PR China)
Xiaoli Cui
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China; Corresponding author.)
Heng Zhu
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China)
Songle Ou
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China)
Zhong Li
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China)
Yutong Gao
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China; School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou, 730050, Gansu, PR China)
Xiao Liu
(College of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen, 361021, PR China)
Wenqing Shi
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China)
Di Tie
(School of Materials Science and Engineering, Guangdong Ocean University, Yangjiang, 529500, PR China; Corresponding author.)
Journal: Journal of Materials Research and Technology
•
• Elsevier
• ISSN: 2238-7854
Abstract
As a candidate cladding material for fourth-generation nuclear energy systems, the microstructure and properties of oxide dispersion strengthened 316L (ODS-316L) steel are significantly affected by heat treatment (HT) processes. This paper highlights the influence mechanism of HT temperature on the microstructural evolution and corrosion resistance of ODS-316L alloys prepared by laser powder bed fusion (LPBF) technology. The results show that HT can significantly regulate the microstructure of ODS-316L alloys. After heat treatment, the ODS-316L alloy consists of a single austenitic phase, indicating no phase transformation occurs before and after heat treatment. With the increase of HT temperature, the fish-scale molten pool morphology characteristic of the as-fabricated ODS-316L alloy disappears, and recrystallized grains coarsen. When the HT temperature reaches 1150 °C, the grain size reaches a maximum of 43.1 μm, the proportion of low-angle grain boundaries (LAGBs) is the highest at 76.7 %, and the Kernel Average Misorientation (KAM) value drops to a minimum of 0.28°. At the HT temperature of 1150 °C, the alloy exhibits excellent corrosion resistance: the self-corrosion potential (Ecorr) reaches a maximum of −0.255 V, the self-corrosion current density (Icorr) decreases to a minimum of 7.797 × 10−7 A/cm2, the pitting potential (Ep) reaches a maximum of 0.632 V, and the passivation interval reaches a maximum of 0.659 V. Moreover, two types of nano-oxide particles, Y–Si–O and Si–O, are uniformly distributed in the 316L matrix heat-treated at 1150 °C, which helps to reduce the self-corrosion current density, thereby improving its corrosion resistance. Furthermore, the correlation between nano-oxides and corrosion resistance is elaborate. This study provides a theoretical basis and reference value for further optimizing the microstructure and corrosion resistance of nuclear-grade ODS-316L alloy components.
Qian Zheng, Chao Lu, Yan Yin, et al. (2025). "Effect of heat treatment on the microstructure and corrosion resistance of laser powder bed fusion ODS-316L". Journal of Materials Research and Technology. https://doi.org/10.1016/j.jmrt.2025.09.256