Impact of biomass ash content on biocomposite properties
Xianhui Zhao
(Manufacturing Science Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States; Environmental Sciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States; Corresponding authors.)
Oluwafemi Oyedeji
(Environmental Sciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States; Corresponding authors.)
Erin Webb
(Environmental Sciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States)
Sanjita Wasti
(Tickle College of Engineering, University of Tennessee, 37996 Knoxville, Tennessee, United States)
Samarthya Bhagia
(Joint Institute for Biological Sciences, Biosciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States)
Holly Hinton
(Chemical Sciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States)
Kai Li
(Buildings and Transportation Science Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States)
Keonhee Kim
(Center for Renewable Carbon, University of Tennessee, 37996 Knoxville, Tennessee, United States)
Ying Wang
(Department of Mechanical and Industrial Engineering, Northeastern University, 02115 Boston, Massachusetts, United States)
Hongli Zhu
(Department of Mechanical and Industrial Engineering, Northeastern University, 02115 Boston, Massachusetts, United States)
Uday Vaidya
(Manufacturing Science Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States; Tickle College of Engineering, University of Tennessee, 37996 Knoxville, Tennessee, United States)
Nicole Labbé
(Center for Renewable Carbon, University of Tennessee, 37996 Knoxville, Tennessee, United States)
Halil Tekinalp
(Manufacturing Science Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States)
Nidia C. Gallego
(Chemical Sciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States)
Yunqiao Pu
(Joint Institute for Biological Sciences, Biosciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States)
Arthur J. Ragauskas
(Joint Institute for Biological Sciences, Biosciences Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States; Department of Chemical and Biomolecular Engineering, University of Tennessee, 37996 Knoxville, Tennessee, United States; Department of Forestry, Wildlife, and Fisheries, Center for Renewable Carbon, The University of Tennessee Institute of Agriculture, 37996 Knoxville, Tennessee, United States)
Soydan Ozcan
(Manufacturing Science Division, Oak Ridge National Laboratory, 1 Bethel Valley Road, 37830 Oak Ridge, Tennessee, United States; Corresponding authors.)
Journal: Composites Part C: Open Access
•
• Elsevier
• ISSN: 2666-6820
Abstract
Owing to its low cost and sustainable nature, lignocellulosic biomass has been utilized for reinforcing polymers, but it is crucial to understand the impact of high-ash concentrations in biomass on composite strength and processing. Biomass is not only desirable for biofuel production but could also have a strong market, if high-ash biomass is acceptable, for biocomposites. In this work, natural fibers (switchgrass and corn stover) were used to reinforce polylactic acid (PLA) to produce biocomposites. Natural fibers were pretreated to obtain fibers that contain different percentages of ash. The mechanical properties (such as Young's modulus, tensile strength, failure strain, storage modulus) of corn stover/PLA composites remained largely unaffected by the ash concentration of the biomass fibers, despite the large range of ash contents (2.2–11.9 wt%). However, the tensile strengths of switchgrass/PLA composites were slightly negatively affected by the ash concentration of the switchgrass fibers (0.7–2.1 wt%). Both the switchgrass/PLA and the corn stover/PLA composites exhibited a high-enough tensile strength (49–57 MPa) and suitable complex viscosity (2.0−7.0 kPa·s at the frequency of 3.2 rad/s). They are expected to be 3D-printable through an extrusion-based additive manufacturing process.
Xianhui Zhao, Oluwafemi Oyedeji, Erin Webb, et al. (2022). "Impact of biomass ash content on biocomposite properties". Composites Part C: Open Access. https://doi.org/10.1016/j.jcomc.2022.100319